Description
ALL in ONE POLYURETHANE PAINT X-88 is a 2-component marine-grade coating based on aliphatic polyurethane with outstanding anticorrosion properties. It is suitable for most surfaces such as wood, iron, aluminum, copper, polyester, concrete, stone, ceramics and many other difficult surfaces when prepared properly. It offers high performance, excellent adhesion, elasticity and hardness and is highly resistant to abrasion and mechanical stress. It is highly resistant to chemicals, solvents, petroleum and mild caustic liquids. Its special aliphatic polyurethane formulation provides excellent protection from exposure to sunlight and from adverse weather conditions, especially for industrial places, close to the sea or exposed to heavy atmospheric pollution. Provides a durable and long-lasting finish. Suitable for indoor and outdoor use.
ADVANTAGES
- Excellent adhesion, hardness, and elasticity
- High resistance to friction and mechanical stress
- High resistance to chemical solvents, petroleum, and mild caustic liquids
- Excellent protection against adverse weather conditions
- Ensures a durable and long-lasting finish
- Excellent color and gloss retention
- Superior UV resistance
- High coverage
- Good application properties
APPLICATIONS
Suitable for painting:
- Metal surfaces such as railings, doors, metal constructions, and general metal structures such as metal bridges and metal fuel tanks (externally).
- Wooden surfaces such as shutters, doors, paneling, fences, etc.
- Concrete surfaces such as floors, microcement coatings, showers, walls, pools, jacuzzi, etc.
- Reinforced fiberglass in boats, yachts, panels.
- Stone wall and floor coverings.
- Many other surfaces when prepared properly for marine and industrial applications or any other application when top performance is required.
Specifications
 |
 |
 |
 |
|
Coverage:
120 – 150 gr/m2 per coat, apply at least 2 coats
|
Thinning:
5% to 20% with DIL X 100 solvent
|
Application:
by brush
|
Application:
by roller
|
 |
 |
 |
 |
|
Application:
by spray gun
|
Touch dry:
4 hours
|
Hard dry:
7 - 10 days
|
Exterior use
|
 |
 |
 |
|
|
|
Interior use
|
Application temperature:
+5oC - 38oC
|
Cleaning:
With DIL X 100 solvent
|
|
|
Instructions for use
Surface preparation
- Surfaces must be clean and dry. Dust, oils, salts, moisture, and rust prevent the adhesion of the paint.
- Surfaces already painted must be thoroughly cleaned by chemical or mechanical means and thoroughly sanded.
- Loose surfaces are unsuitable for painting and the paint will peel off.
- New concrete surfaces must be painted at least one month after their construction.
- If the surface is washed with water, it must be dried for 2-3 days before painting.
Priming
Tiles, sanitary ware and generally smooth non-porous surfaces are primed with ALL in ONE EPOXY PRIMER P-76 to ensure increased adhesion and durability.
Concrete surfaces are primed with ALL in ONE EPOXY PRIMER P-76 to stabilize and strengthen them. Concrete surfaces that experience rising moisture are primed with a 100% solids (solvent-free) two-component epoxy primer EPOXITE DRYMAX WET.
Metal or aluminum surfaces are recommended to be primed with ALL in ONE EPOXY PRIMER P-76 anti-rust and anti-corrosion epoxy primer for additional protection against corrosion. Otherwise, degrease with thinner and apply paint directly.
On new wooden surfaces, apply the paint directly after sanding the surface and removing dust. Degrease oily wood with acetone or nitro solvent. For marine applications or if the wood is not in good condition, old coatings must be mechanically removed and ALL in ONE EPOXY PRIMER P-76 must be applied.
Polyester surfaces should be sanded and dust cleaned before painting. For greater durability and strong anti-osmotic protection, prime with ALL in ONE EPOXY PRIMER P-76.
On stone surfaces, apply directly if the stone is firm. If the stone is brittle, strengthen it with the transparent epoxy primer EPOXITE DUR.
Application
- Components Α (resin) and Β (hardener) are already packed in separate containers with a preset mixing ratio. Any modification of the mixing ratio will result in improper polymerization of the mixture.
- Mix the two components after carefully mixing component A separately. Mixing is done carefully for 3-5 minutes using an electric mixer (approx. 300 rpm), ensuring thorough mixing of the two components on the walls and the bottom of the pail.
- Imperfect mixing will result in uneven curing of the coating, with parts that will not cure at all.
- After mixing the two components, let the mixture stand for 5 minutes and then apply the coating diluted with DIL X 100, 5% - 10% for roller and brush application, and 10% - 20% for spray gun application.
- Apply two or three coats. Wait 12h (25oC) – 24h (10oC) to recoat.
- The coating obtains its final properties 7 - 10 days after the application of the final coat.
- Before application, read carefully all instructions and information relevant to its safe and best use (Safety Data Sheet).
REMARKS
- ALL in ONE POLYURETHANE PAINT X-88 contains solvents. Ventilate the working area adequately. It is advised to use protective gloves and a mask suitable for solvents.
- Application conditions: Substrate’s moisture: <4%, Surface and Ambient temperature: 12oC - 35oC, Relative Air Humidity: <70%.
- It is advisable to use protective clothing, gloves, a hat, and a mask with a filter suitable for solvents.
- Freshly painted surfaces must be protected from excessive humidity and rain for 36 – 48 hours.
- If recoating is carried out after 36 hours, the surface must be sanded with coarse sandpaper and dust must be removed.
- Curing as well as pot life are affected by ambient temperature and humidity. Low temperatures and high humidity tend to increase pot life, while high temperatures and low humidity shorten the pot life.
- Treatments such as sanding, flame cleaning, etc., of painted surfaces can create hazardous dust and fumes. Work in a well-ventilated area. Use appropriate personal protective equipment.
- Avoid painting surfaces in direct sunlight because bubbles may form on the surface of the paint.
- The substrate must be at least 3oC above the dew point to reduce the risk of condensation or blooming on the paint’s finish.
