Specifications

Coverage: 300 - 350gr/m2 for 2 layers	Thinning: 0 - 10% with DIL X 100 solvent	Application: by brush	Application: by roller
Application: by spray gun	Recoating: 12 - 24 hours (for temperatures 30oC and 12oC respectively)	Final Curing time: 7 - 14 days	Exterior use
Interior use	Application temperature: 10oC - 35oC	Cleaning: with DIL X 100, nitro or polyurethane solvent

Instructions for use

Surface preparation

1. Surfaces must be dry and clean from dust and any oily residues. Dust, oil, humidity or rust seriously affect the coating’s adhesion.
2. Loose substrates of concrete and screeds are not suitable for painting as the coat will peel.
3. New surfaces of concrete or cement mortar must be painted one month after construction.
4. Surfaces already painted must be completely cleaned with chemical or mechanical means and sanded to a smooth finish.
5. The wet surface must be allowed to dry for at least 2 - 5 days prior to the paint application.
6. Old flaking, chalking paints or discolorations must be completely removed with mechanical means.

Priming

• Prime surfaces with EPOXITE DUR solvent based epoxy primer.
• Surfaces with rising humidity should be primed with 100% solids solvent free, epoxy primer EPOXITE DRY MAX WET.

Application

1. Allow 12 - 24 hours after priming.
2. Components Α (resin) and Β (hardener) are already packed in separate containers with a preset mixing ratio (100Α:25Β). Any modification of the mixing ratio will result in improper polymerization of the mixture.
3. Mix the 2 components after carefully mixing each component separately.
4. Stirring is done carefully for 3 - 5 minutes taking care to ensure thorough mixing of the two components on the walls and the bottom of the pail.
5. Imperfect mixing will result in uneven curing of the coating with parts that will not cure at all.
6. After mixing of the two components allow 5 - 10 minutes and then apply the coating as is or diluted up to 10% with DIL X 100 solvent
7. It is suggested to apply 2 or 3 layers and let each layer dry for 12 to 24 hours before the next one (for temperatures 30^oC and 12^oC respectively).
8. Application is done with a brush, roller, or spray gun.
9. When painting new pools it is recommended to apply 3 coats. When repainting old pools, 2 coats are recommended.
10. The paint obtains its final properties 7 - 14 days after the application of the finishing coat depending on ambient temperature and humidity.

REMARKS

• Application conditions: Substrate’s moisture: <4%, Surface’s and Ambient temperature: 12^oC - 35^oC, Relative Air Humidity: <70%.
• Do not paint during direct sunlight exposure. There is danger of affecting the durability of the final coating.
• PREMIUM POLYURETHANE POOL PAINT 2K contains solvents and during application good ventilation of the space should be ensured.
• It is advisable to use protective clothing, gloves, and mask with filter suitable for solvents.
• The coated surface should be protected from humidity for 36 - 48 hours.
• Should recoating be carried out after 48 hours, the surface must be sanded with coarse sandpaper and dust must be removed.
• Curing and pot – life are affected by ambient temperature and humidity. Low temperatures and high humidity tend to increase pot – life while high temperatures and low humidity shorten the pot life.
• Before using PREMIUM POLYURETHANE POOL PAINT 2K carefully read all instructions and information relevant to its safe and best use.
• The substrate must be at least 3^oC above dew point to reduce the risk of condensation or blooming on the paint’s finish.
• After fully cured, PREMIUM POLYURETHANE POOL PAINT 2K is totally safe for health.